Page 1 of 2
KX500 V-FORCE 2 REED VALVES FOR SALE
Posted: Mon Mar 17, 2014 10:02 pm
by Sandblaster
KX500 V-FORCE 2 REED VALVES FOR SALE
Brand new.
You will not receive a factory box or literature.
170.00 each delivered anywhere in the USA by priority mail (2-4 days)
Or you can spend another 30 bucks and buy them through eBay
http://www.ebay.com/itm/KX500-KAWASAKI- ... 464cc83d1f
- KX500 V FORCE 2 REED VALVE 1.JPG (52.81 KiB) Viewed 15838 times
- KX500 V FORCE 2 REED VALVE 2.JPG (42.11 KiB) Viewed 15838 times
Re: KX500 V-FORCE 2 REED VALVES FOR SALE
Posted: Mon Mar 17, 2014 10:03 pm
by Sandblaster
- KX500 V FORCE 2 REED VALVE 3.JPG (59.31 KiB) Viewed 15837 times
- KX500 V FORCE 2 REED VALVE 4.JPG (60.64 KiB) Viewed 15837 times
Re: KX500 V-FORCE 2 REED VALVES FOR SALE
Posted: Fri Mar 28, 2014 8:00 pm
by Sandblaster
I have bad news, good news, and bad news.
The bad news is I ran out of stock
The good news is I have a new supplier .
Re: KX500 V-FORCE 2 REED VALVES FOR SALE
Posted: Thu Apr 03, 2014 8:41 pm
by Sandblaster
Should have a couple more to sell 4-4-14
Re: KX500 V-FORCE 2 REED VALVES FOR SALE
Posted: Fri Apr 22, 2016 5:26 am
by Sandblaster
4-21-16... Got a few more new VF2 reeds for the KX500
Get them quick!
Re: KX500 V-FORCE 2 REED VALVES FOR SALE
Posted: Sat Apr 23, 2016 2:12 pm
by Sandblaster
Re: KX500 V-FORCE 2 REED VALVES FOR SALE
Posted: Sun Apr 24, 2016 8:53 am
by dirk_411
You mean this round of them are almost gone.... they are going into full production again says jeff
Re: KX500 V-FORCE 2 REED VALVES FOR SALE
Posted: Sun Apr 24, 2016 2:56 pm
by Sandblaster
I bought 6 of the KX500's and 4 of the CR500's and I have only one left.
Probably will sell that one today or tonight.
When I ordered them about a week ago, Jeff said that they may or may not be building more.
Apparently there was still some discussion on it.
So, I guess we will have to wait and see.
I'm trying to order more but at this point I'm not going to hold my breath
Re: KX500 V-FORCE 2 REED VALVES FOR SALE
Posted: Sun Apr 24, 2016 9:02 pm
by dirk_411
I'll buy it from you. Jeff sounded certain when I broke the news at kxriders.net that they were going back into full swing.....
Also wanted to ask you. For my 98-99 kx250 cylinder, would you have a head and 2 coolant elbows, the inlet elbow just about the intake.... I'd maybe take 3 if ya had them. Not sure what other years are the same?
Re: KX500 V-FORCE 2 REED VALVES FOR SALE
Posted: Sun Apr 24, 2016 9:15 pm
by Sandblaster
Oh man... I already sold the last one...
I hope we can get some more...
I'll check on the other parts for you in a bit
